DPSS 532nM Laser
| Stable 532nM Laser
|
|
General Specifications:
Wavelength: 532nM
Beam Divergence: As low as 0.25mrad
Output Power: up to 250mW.
Complete laser head and laser driver.
Operating Current: as low as 150mA
Power Stability: as low as 2%./hr
Size: as small as Dia. 12 x 20mm
Operating temperature: 15 - 35 Ž
Optional TEC
|
NEW Micro watt power 532nM Laser Module
Item No.: GM32-005MIC
|
Output power, CW: 2 to 5 ƒÊW ,adjustable, TEMoo
Line width: < 0.2 nM
Power stability: < 2.5%
Pointing stability: 50 ƒÊm
Beam spot diameter at 250 mm (1/e2): < 50 ƒÊm
Laser Head Size: 20 x 112 mm
Operating voltage: 3.3 to 6 VDC |
External access to optical feed back signal
Built-in safety feature shuts down laser in event power feedback control fails
Preset absolute peak output power of 250 ƒÊW for safety back up
Individually tested to guarantee proper operation within 19 - 50Ž range
All parameters can be configured to specified values per end user requirement
NEW Single longitudinal mode 532nM Laser Module
Transverse mode: TEMoo, M2<1.2 (typ.1.1)
Longitudinal Modes: Single longitudinal mode
Line width: < 0.00001 nM
Coherence length: >10 meter
Polarization linearity: >100:1, horizontal
Ellipticity: 0.95-1.05
Beam waist position: 22 mm behind the face
Beam diameter at output: <0.25 mm
Transverse beam position accuracy: }0.3 mm
Beam alignment accuracy: }3 mrad
Beam waist position accuracy: }0.5 mm
Polarization orientation accuracy: }3‹
Noise (10-20MHz): <0.5% RMS (typ. 0.1% RMS)
Long term stability: 2% / 8 hrs
Beam height to the laser head base: 0.669'' |
Warm-up time: <10 min (typ. 5 min)
Warm-up time from standby mode: 10 sec
Cable length: max. 1 meter
Connector type: IDC-24
Housing base temperature range: 15-50 Ž
Heating power: <10 W (typ. 6 W)
Laser Head Size: 65 x 40 x 29 mm
Laser Head Weight: 150 g
Laser Driver Size: 85 x 60 x 25 mm
Iop: < 1.8 A
Vop: 4.5 to 6 VDC
Beam Divergence: 10}1 (mrad, full angle, 1/e2)
Beam Waist Diameter: 0.070}0.007 (mm, 1/e2)
Mounting plate thickness: 3/8'' |
|
|
Item No. |
Po (mW) max. |
GM32-5SL |
5 |
GM32-10SL |
10 |
GM32-20SL |
20 |
|
Optional Beam Expander
Beam Expander |
Laser head with Beam Expander |
Item No.
| Beam diameter at output, mm |
Beam divergence at full angle, mrad |
O-E02-0.6 |
1.1}0.1 |
0.6}0.1 |
O-E02-0.5 |
1.6}0.2 |
0.5}0.1 |
O-E02-3.0 |
0.22}0.02 |
3.0}0.3 |
O-E02-2.4 |
0.33}0.03 |
2.4}0.2 |
O-E02-0.33 |
2.2}0.2 |
0.33}0.05 |
|
Single transverse mode 532nM Laser Module
Please click on the Item No. for detail specifications
Item No.: GM32-1VP
|
- Wavelength: 532 nM
- Output Power: 1 mW, CW
- Transverse Mode: TEMoo
- Power Stability: 5 - 10%
- Beam Divergence (Half angle 1/e2): 0.5 } 0.1mrad
- Beam Diameter at output: %lt; 1.0 } 0.2 mm
- Size : Dia. 15.0 x 90.0 mm
- Single Unit Configuration (laser head and driver in one housing)
- Operating Voltage / Current: 3.0 VDC / 400 mA
- Operating Temperature Ranger: 15 - 35 Ž
- Optional Modulation Control (Item No.: MCON)
- Optional Power Adjustment (Item No.: PADJ)
- Optional Power Supply (Item No.:PS-3V3A)
- Optional Laser Module Mount
|
Item No.: GM32-1F
|
- Wavelength: 532 nM
- Output Power: 1 mW, CW
- Transverse Mode: TEMoo
- Power Stability: 10 - 20%
- Beam Divergence (Half angle 1/e2): 0.5 } 0.1mrad
- Beam Diameter at output: %lt; 1.0 } 0.2 mm
- Size : Dia. 12.5 x 53.0 mm
- Single Unit Configuration (laser head and driver in one housing)
- Operating Voltage / Current: 3.0 VDC / 250 mA
- Operating Temperature Ranger: 15 - 35 Ž
- Optional Modulation Control (Item No.: MCON)
- Optional Power Adjustment (Item No.: PADJ)
- Optional Power Supply (Item No.: PS-3V3A)
- Optional Laser Module Mount
|
Item No.: GM32-3F
|
- Wavelength: 532 nM
- Output Power: 3 mW, CW
- Transverse Mode: TEMoo
- Power Stability: 10 - 20%
- Beam Divergence (Half angle 1/e2): 0.5 } 0.1mrad
- Beam Diameter at output: %lt; 1.0 } 0.2 mm
- Size : Dia. 12.5 x 53.0 mm
- Single Unit Configuration (laser head and driver in one housing)
- Operating Voltage / Current: 3.0 VDC / 280 mA
- Operating Temperature Ranger: 15 - 35 Ž
- Optional Modulation Control (Item No.: MCON)
- Optional Power Adjustment (Item No.: PADJ)
- Optional Power Supply (Item No.: PS-3V3A)
- Optional Laser Module Mount
|
Item No.: GM32-5F
|
- Wavelength: 532 nM
- Output Power: 5 mW, CW
- Transverse Mode: TEMoo
- Power Stability: 10 - 20%
- Beam Divergence (Half angle 1/e2): 0.5 } 0.1mrad
- Beam Diameter at output: %lt; 1.0 } 0.2 mm
- Size : Dia. 12.5 x 53.0 mm
- Single Unit Configuration (laser head and driver in one housing)
- Operating Voltage / Current: 3.0 VDC / 300 mA
- Operating Temperature Ranger: 15 - 35 Ž
- Optional Modulation Control (Item No.: MCON)
- Optional Power Adjustment (Item No.: PADJ)
- Optional Power Supply (Item No.: PS-3V3A)
- Optional Laser Module Mount
|
Item No.: GM32-1G
|
- Wavelength: 532 nM
- Output Power: 1 mW, CW
- Transverse Mode: TEMoo
- Power Stability: 10 - 15%
- Beam Divergence (Half angle 1/e2): 0.5 } 0.1mrad
- Beam Diameter at output: %lt; 1.0 } 0.2 mm
- Size : Dia. 15.0 x 60.0 mm
- Single Unit Configuration (laser head and driver in one housing)
- Operating Voltage / Current: 3.0 VDC / 400 mA
- Operating Temperature Ranger: 15 - 35 Ž
- Optional Modulation Control (Item No.: MCON)
- Optional Power Adjustment (Item No.: PADJ)
- Optional Power Supply (Item No.: PS-3V3A)
- Optional Laser Module Mount
|
Item No.: GM32-3G
|
- Wavelength: 532 nM
- Output Power: 3 mW, CW
- Transverse Mode: TEMoo
- Power Stability: 10 - 15%
- Beam Divergence (Half angle 1/e2): 0.5 } 0.1mrad
- Beam Diameter at output: %lt; 1.0 } 0.2 mm
- Size : Dia. 15.0 x 60.0 mm
- Single Unit Configuration (laser head and driver in one housing)
- Operating Voltage / Current: 3.0 VDC / 400 mA
- Operating Temperature Ranger: 15 - 35 Ž
- Optional Modulation Control (Item No.: MCON)
- Optional Power Adjustment (Item No.: PADJ)
- Optional Power Supply (Item No.: PS-3V3A)
- Optional Laser Module Mount
|
Item No.: GM32-5G
|
- Wavelength: 532 nM
- Output Power: 5 mW, CW
- Transverse Mode: TEMoo
- Power Stability: 10 - 15%
- Beam Divergence (Half angle 1/e2): 0.5 } 0.1mrad
- Beam Diameter at output: %lt; 1.0 } 0.2 mm
- Size : Dia. 15.0 x 60.0 mm
- Single Unit Configuration (laser head and driver in one housing)
- Operating Voltage / Current: 3.0 VDC / 450 mA
- Operating Temperature Ranger: 15 - 35 Ž
- Optional Modulation Control (Item No.: MCON)
- Optional Power Adjustment (Item No.: PADJ)
- Optional Power Supply (Item No.: PS-3V3A)
- Optional Laser Module Mount
|
Item No.: GM32-10G
|
- Wavelength: 532 nM
- Output Power: 10 mW, CW
- Transverse Mode: TEMoo
- Power Stability: 10 - 15%
- Beam Divergence (Half angle 1/e2): 0.5 } 0.1mrad
- Beam Diameter at output: %lt; 1.0 } 0.2 mm
- Size : Dia. 15.0 x 60.0 mm
- Single Unit Configuration (laser head and driver in one housing)
- Operating Voltage / Current: 3.0 VDC / 450 mA
- Operating Temperature Ranger: 15 - 35 Ž
- Optional Modulation Control (Item No.: MCON)
- Optional Power Adjustment (Item No.: PADJ)
- Optional Power Supply (Item No.: PS-3V3A)
- Optional Laser Module Mount
|
Item No.: GM32-05GS
|
- Wavelength: 532 nM
- Output Power: 0.5 mW, CW
- Transverse Mode: TEMoo
- Power Stability at constant housing temperature: < 2% per 8 hrs
- Power Stability at drifting housing temperature: < 5% per 10 Ž
- Beam Divergence (Half angle 1/e2): 0.6 } 0.1mrad
- Beam Diameter at output: %lt; 1.0 } 0.2 mm
- Polarization Linearity: > 50 : 1
- Size : Dia. 14.8 x 112.0 mm
- Cable length: 16 inches (40cm)
- Operating Voltage / Current: 3.3 - 3.5 VDC / 1.4 A
- Operating Temperature Ranger: 15 - 35 Ž
- Heating Power (at 3.3VDC): max. 4.6 W
- Optional Power Supply (Item No.: PS-3V3A)
|
Item No.: GM32-5GS
|
- Wavelength: 532 nM
- Output Power: 5 mW, CW
- Transverse Mode: TEMoo
- Power Stability at constant housing temperature: < 2% per 8 hrs
- Power Stability at drifting housing temperature: < 5% per 10 Ž
- Beam Divergence (Half angle 1/e2): 0.6 } 0.1mrad
- Beam Diameter at output: %lt; 1.0 } 0.2 mm
- Polarization Linearity: > 50 : 1
- Size : Dia. 14.8 x 112.0 mm
- Cable length: 16 inches (40cm)
- Operating Voltage / Current: 3.3 - 3.5 VDC / 1.4 A
- Operating Temperature Ranger: 15 - 35 Ž
- Heating Power (at 3.3VDC): max. 4.6 W
- There are three 0.25''-20 mounting holes on laser head
- Optional Power Supply (Item No.: PS-3V3A)
|
Item No.: GM32-10GS
|
- Wavelength: 532 nM
- Output Power: 20 mW, CW
- Transverse Mode: TEMoo
- Power Stability at constant housing temperature: < 2% per 8 hrs
- Power Stability at drifting housing temperature: < 5% per 10 Ž
- Beam Divergence (Half angle 1/e2): 0.6 } 0.1mrad
- Beam Diameter at output: %lt; 1.0 } 0.2 mm
- Polarization Linearity: > 50 : 1
- Size : Dia. .995 x 5.0 inches
- Cable length: 16 inches (40cm)
- Operating Voltage / Current: 3.3 - 3.5 VDC / 1.4 A
- Operating Temperature Ranger: 15 - 35 Ž
- Heating Power (at 3.3VDC): max. 4.6 W
- There are three 0.25''-20 mounting holes on laser head
- Optional Power Supply (Item No.: PS-3V3A)
|
Item No.: GM32-20GS
|
- Wavelength: 532 nM
- Output Power: 20 mW, CW
- Transverse Mode: TEMoo
- Power Stability at constant housing temperature: < 2% per 8 hrs
- Power Stability at drifting housing temperature: < 5% per 10 Ž
- Beam Divergence (Half angle 1/e2): 0.6 } 0.1mrad
- Beam Diameter at output: %lt; 1.0 } 0.2 mm
- Polarization Linearity: > 50 : 1
- Size : Dia. .995 x 5.0 inches
- Cable length: 16 inches (40cm)
- Operating Voltage / Current: 3.3 - 3.5 VDC / 1.4 A
- Operating Temperature Ranger: 15 - 35 Ž
- Heating Power (at 3.3VDC): max. 4.6 W
- There are three 0.25''-20 mounting holes on laser head
- Optional Power Supply (Item No.: PS-3V3A)
|
Item No.: GM32-40GS
|
- Wavelength: 532 nM
- Output Power: 40 mW, CW
- Transverse Mode: TEMoo
- Power Stability at constant housing temperature: < 2% per 8 hrs
- Power Stability at drifting housing temperature: < 5% per 10 Ž
- Beam Divergence (Half angle 1/e2): 0.6 } 0.1mrad
- Beam Diameter at output: %lt; 1.0 } 0.2 mm
- Polarization Linearity: > 50 : 1
- Size : Dia. .995 x 5.0 inches
- Cable length: 16 inches (40cm)
- Operating Voltage / Current: 3.3 - 3.5 VDC / 1.4 A
- Operating Temperature Ranger: 15 - 35 Ž
- Heating Power (at 3.3VDC): max. 4.6 W
- There are three 0.25''-20 mounting holes on laser head
- Optional Power Supply (Item No.: PS-3V3A)
|
Item No.: GM32-50GSA-P10
|
- Wavelength: 532 nM
- Output Power: 50 mW, CW
- Transverse Mode: TEMoo
- Power Stability: < 5%
- Line Width: 0.1 nm
- Polarization Ratio: 10:1
- Beam Divergence (Full angle 1/e2): 1.0 mrad (Optional 0.5 mrad)
- Beam Diameter (1/e2): < 2.0 mm
- Noise (RMS. 20 Hz - 20 MHz): 20 % around 50 - 200 KHz
- Ellipticity: 0.95 -1.05
- TTL Modulation Control (> 30 KHz)
- Laser head size (W x L x H): 35 x 110 x 35 mm
- Laser driver size(W x L x H): 72 x 105 x 30 mm
- Cable length: 32 inches (81cm)
- Operating Voltage / Current: 12 VDC / 3 A
- Operating Temperature Ranger: 0 - 40 ° C
|
Item No.: GM32-100GSA-P10
|
- Wavelength: 532 nM
- Output Power: 100 mW, CW
- Transverse Mode: TEMoo
- Power Stability: < 5%
- Line Width: 0.1 nm
- Polarization Ratio: 10:1
- Beam Divergence (Full angle 1/e2): 1.0 mrad (Optional 0.5 mrad)
- Beam Diameter (1/e2): < 2.0 mm
- Noise (RMS. 20 Hz - 20 MHz): 20 % around 50 - 200 KHz
- Ellipticity: 0.95 -1.05
- TTL Modulation Control (> 30 KHz)
- Laser head size (L x W x H): 135 x 50 x 42 mm
- Laser driver size(L x W x H): 105 x 72 x 30 mm
- Cable length: 32 inches (81cm)
- Operating Voltage / Current: 12 VDC / 3 A
- Operating Temperature Ranger: 0 - 40 ° C
|
Item No.: GM32-200GSA-P10
|
- Wavelength: 532 nM
- Output Power: 200 mW, CW
- Transverse Mode: TEMoo
- Power Stability: < 5%
- Line Width: 0.1 nm
- Polarization Ratio: 10:1
- Beam Divergence (Full angle 1/e2): 1.0 mrad (Optional 0.5 mrad)
- Beam Diameter (1/e2): < 2.0 mm
- Noise (RMS. 20 Hz - 20 MHz): 20 % around 50 - 200 KHz
- Ellipticity: 0.95 -1.05
- TTL Modulation Control (> 30 KHz)
- Laser head size (L x W x H): 135 x 50 x 42 mm
- Laser driver size(L x W x H): 105 x 72 x 30 mm
- Cable length: 32 inches (81cm)
- Operating Voltage / Current: 12 VDC / 3 A
- Operating Temperature Ranger: 0 - 40 ° C
|
Item No.: GM32-50GSA-P100
|
- Wavelength: 532 nM
- Output Power: 50 mW, CW
- Transverse Mode: TEMoo
- Power Stability: < 5%
- Line Width: 0.1 nm
- Polarization Ratio: 100:1
- Beam Divergence (Full angle 1/e2): 1.0 mrad (Optional 0.5 mrad)
- Beam Diameter (1/e2): < 2.0 mm
- Noise (RMS. 20 Hz - 20 MHz): 20 % around 50 - 200 KHz
- Ellipticity: 0.95 -1.05
- TTL Modulation Control (> 30 KHz)
- Laser head size (W x L x H): 35 x 110 x 35 mm
- Laser driver size(W x L x H): 72 x 105 x 30 mm
- Cable length: 32 inches (81cm)
- Operating Voltage / Current: 12 VDC / 3 A
- Operating Temperature Ranger: 0 - 40 ° C
|
Item No.: GM32-100GSA-P100
|
- Wavelength: 532 nM
- Output Power: 100 mW, CW
- Transverse Mode: TEMoo
- Power Stability: < 5%
- Line Width: 0.1 nm
- Polarization Ratio: 100:1
- Beam Divergence (Full angle 1/e2): 1.0 mrad (Optional 0.5 mrad)
- Beam Diameter (1/e2): < 2.0 mm
- Noise (RMS. 20 Hz - 20 MHz): 20 % around 50 - 200 KHz
- Ellipticity: 0.95 -1.05
- TTL Modulation Control (> 30 KHz)
- Laser head size (L x W x H): 135 x 50 x 42 mm
- Laser driver size(L x W x H): 105 x 72 x 30 mm
- Cable length: 32 inches (81cm)
- Operating Voltage / Current: 12 VDC / 3 A
- Operating Temperature Ranger: 0 - 40 ° C
|
Item No.: GM32-200GSA-P100
|
- Wavelength: 532 nM
- Output Power: 200 mW, CW
- Transverse Mode: TEMoo
- Power Stability: < 5%
- Line Width: 0.1 nm
- Polarization Ratio: 100:1
- Beam Divergence (Full angle 1/e2): 1.0 mrad (Optional 0.5 mrad)
- Beam Diameter (1/e2): < 2.0 mm
- Noise (RMS. 20 Hz - 20 MHz): 20 % around 50 - 200 KHz
- Ellipticity: 0.95 -1.05
- TTL Modulation Control (> 30 KHz)
- Laser head size (L x W x H): 135 x 50 x 42 mm
- Laser driver size(L x W x H): 105 x 72 x 30 mm
- Cable length: 32 inches (81cm)
- Operating Voltage / Current: 12 VDC / 3 A
- Operating Temperature Ranger: 0 - 40 ° C
|
Item No.: GM32-1H
Standard OEM Driver
Turnkey Driver
|
- Wavelength: 532 nM
- Output Power: 1 mW, CW
- Transverse Mode: TEMoo
- Power Stability: 5 - 10%
- Beam Divergence (Half angle 1/e2): 0.5 } 0.1mrad
- Beam Diameter at output: %lt; 1.0 } 0.2 mm
- Laser Size : Dia. 12.5 x 60.0 mm
- Standard OEM LD-E Driver Size: 30.15 x 35.56 x 14 mm
- Operating Voltage / Current: 3.0 - 5.0 VDC / 300 mA
- Operating Temperature Ranger: 15 - 35 Ž
- Cable Length (connect laser and driver: 8 inches
- Input Leads Length: 8 inches.
- Optional Turnkey Driver (Item No.: LD-C)
- Input Voltage / Current: 5 VDC / 350 mA
- Size: 50 x 50 x 42mm
- Quick disconnect DC Input Power Jack
- On/Off Switch with built_in LED Indicator
- Heat Sink
- Optional Modulation Control (Item No.: MCON)
- Optional Power Adjustment (Item No.: PADJ)
- Optional Power Supply PS-5V2A for OEM Driver
- Optional Power Supply PS-5V1A for Turnkey Driver
- Optional Laser Module Mount
|
Item No.: GM32-3H
Standard OEM Driver
Turnkey Driver
|
- Wavelength: 532 nM
- Output Power: 3 mW, CW
- Transverse Mode: TEMoo
- Power Stability: 5 - 10%
- Beam Divergence (Half angle 1/e2): 0.5 } 0.1mrad
- Beam Diameter at output: %lt; 1.0 } 0.2 mm
- Laser Size : Dia. 12.5 x 60.0 mm
- Standard OEM LD-E Driver Size: 30.15 x 35.56 x 14 mm
- Operating Voltage / Current: 3.0 - 5.0 VDC / 300 mA
- Operating Temperature Ranger: 15 - 35 Ž
- Cable Length (connect laser and driver: 8 inches
- Input Leads Length: 8 inches.
- Optional Turnkey Driver (Item No.: LD-C)
- Input Voltage / Current: 5 VDC / 350 mA
- Size: 50 x 50 x 42mm
- Quick disconnect DC Input Power Jack
- On/Off Switch with built_in LED Indicator
- Heat Sink
- Optional Modulation Control (Item No.: MCON)
- Optional Power Adjustment (Item No.: PADJ)
- Optional Power Supply PS-5V2A for OEM Driver
- Optional Power Supply PS-5V1A for Turnkey Driver
- Optional Laser Module Mount
|
Item No.: GM32-5H
Standard OEM Driver
Turnkey Driver
|
- Wavelength: 532 nM
- Output Power: 5 mW, CW
- Transverse Mode: TEMoo
- Power Stability: 5 - 10%
- Beam Divergence (Half angle 1/e2): 0.5 } 0.1mrad
- Beam Diameter at output: %lt; 1.0 } 0.2 mm
- Laser Size : Dia. 12.5 x 60.0 mm
- Standard OEM LD-E Driver Size: 30.15 x 35.56 x 14 mm
- Operating Voltage / Current: 3.0 - 5.0 VDC / 300 mA
- Operating Temperature Ranger: 15 - 35 Ž
- Cable Length (connect laser and driver: 8 inches
- Input Leads Length: 8 inches.
- Optional Turnkey Driver (Item No.: LD-C)
- Input Voltage / Current: 5 VDC / 350 mA
- Size: 50 x 50 x 42mm
- Quick disconnect DC Input Power Jack
- On/Off Switch with built_in LED Indicator
- Heat Sink
- Optional Modulation Control (Item No.: MCON)
- Optional Power Adjustment (Item No.: PADJ)
- Optional Power Supply PS-5V2A for OEM Driver
- Optional Power Supply PS-5V1A for Turnkey Driver
- Optional Laser Module Mount
|
Item No.: GM32-10H
Standard OEM Driver
Turnkey Driver
|
- Wavelength: 532 nM
- Output Power: 10 mW, CW
- Transverse Mode: TEMoo
- Power Stability: 5 - 10%
- Beam Divergence (Half angle 1/e2): 0.5 } 0.1mrad
- Beam Diameter at output: %lt; 1.0 } 0.2 mm
- Laser Size : Dia. 12.5 x 60.0 mm
- Standard OEM LD-E Driver Size: 30.15 x 35.56 x 14 mm
- Operating Voltage / Current: 3.0 - 5.0 VDC / 350 mA
- Operating Temperature Ranger: 15 - 35 Ž
- Cable Length (connect laser and driver: 8 inches
- Input Leads Length: 8 inches.
- Optional Turnkey Driver (Item No.: LD-C)
- Input Voltage / Current: 5 VDC / 400 mA
- Size: 50 x 50 x 42mm
- Quick disconnect DC Input Power Jack
- On/Off Switch with built_in LED Indicator
- Heat Sink
- Optional Modulation Control (Item No.: MCON)
- Optional Power Adjustment (Item No.: PADJ)
- Optional Power Supply PS-5V2A for OEM Driver
- Optional Power Supply PS-5V1A for Turnkey Driver
- Optional Laser Module Mount
|
Item No.: GM32-15H
Standard OEM Driver
Turnkey Driver
|
- Wavelength: 532 nM
- Output Power: 15 mW, CW
- Transverse Mode: TEMoo
- Power Stability: 5 - 10%
- Beam Divergence (Half angle 1/e2): 0.5 } 0.1mrad
- Beam Diameter at output: %lt; 1.0 } 0.2 mm
- Laser Size : Dia. 12.5 x 60.0 mm
- Standard OEM LD-E Driver Size: 30.15 x 35.56 x 14 mm
- Operating Voltage / Current: 3.0 - 5.0 VDC / 350 mA
- Operating Temperature Ranger: 15 - 35 Ž
- Cable Length (connect laser and driver: 8 inches
- Input Leads Length: 8 inches.
- Optional Turnkey Driver (Item No.: LD-C)
- Input Voltage / Current: 5 VDC / 400 mA
- Size: 50 x 50 x 42mm
- Quick disconnect DC Input Power Jack
- On/Off Switch with built_in LED Indicator
- Heat Sink
- Optional Modulation Control (Item No.: MCON)
- Optional Power Adjustment (Item No.: PADJ)
- Optional Power Supply PS-5V2A for OEM Driver
- Optional Power Supply PS-5V1A for Turnkey Driver
- Optional Laser Module Mount
|
Item No.: GM32-20H
Standard OEM Driver
Turnkey Driver
|
- Wavelength: 532 nM
- Output Power: 20 mW, CW
- Transverse Mode: TEMoo
- Power Stability: 5 - 10%
- Beam Divergence (Half angle 1/e2): 0.5 } 0.1mrad
- Beam Diameter at output: %lt; 1.0 } 0.2 mm
- Laser Size : Dia. 12.5 x 60.0 mm
- Standard OEM LD-E Driver Size: 30.15 x 35.56 x 14 mm
- Operating Voltage / Current: 3.0 - 5.0 VDC / 350 mA
- Operating Temperature Ranger: 15 - 35 Ž
- Cable Length (connect laser and driver: 8 inches
- Input Leads Length: 8 inches.
- Optional Turnkey Driver (Item No.: LD-C)
- Input Voltage / Current: 5 VDC / 400 mA
- Size: 50 x 50 x 42mm
- Quick disconnect DC Input Power Jack
- On/Off Switch with built_in LED Indicator
- Heat Sink
- Optional Modulation Control (Item No.: MCON)
- Optional Power Adjustment (Item No.: PADJ)
- Optional Power Supply PS-5V2A for OEM Driver
- Optional Power Supply PS-5V1A for Turnkey Driver
- Optional Laser Module Mount
|
Item No.: GM32-25H
Standard OEM Driver
Turnkey Driver
|
- Wavelength: 532 nM
- Output Power: 25 mW, CW
- Transverse Mode: TEMoo
- Power Stability: 5 - 10%
- Beam Divergence (Half angle 1/e2): 0.5 } 0.1mrad
- Beam Diameter at output: %lt; 1.0 } 0.2 mm
- Laser Size : Dia. 12.5 x 60.0 mm
- Standard OEM LD-E Driver Size: 30.15 x 35.56 x 14 mm
- Operating Voltage / Current: 3.0 - 5.0 VDC / 350 mA
- Operating Temperature Ranger: 15 - 35 Ž
- Cable Length (connect laser and driver: 8 inches
- Input Leads Length: 8 inches.
- Optional Turnkey Driver (Item No.: LD-C)
- Input Voltage / Current: 5 VDC / 400 mA
- Size: 50 x 50 x 42mm
- Quick disconnect DC Input Power Jack
- On/Off Switch with built_in LED Indicator
- Heat Sink
- Optional Modulation Control (Item No.: MCON)
- Optional Power Adjustment (Item No.: PADJ)
- Optional Power Supply PS-5V2A for OEM Driver
- Optional Power Supply PS-5V1A for Turnkey Driver
- Optional Laser Module Mount
|
|
|